• 地址:山东省济南市高新区邢村立交桥路北
  • 联系人:张经理
  • 手机:18605312229
新闻中心当前位置:首页-新闻中心
    数控刀片回收厂家告诉你丝锥断了怎么办?
    来源:http://www.hxdphs.com/ 2019-7-27 15:27:42

  丝锥在许多行业中都有应用,但现代加工中经常出现丝锥、钻头断裂、螺杆滑动齿生锈等现象

  Taper is widely used in many industries, but in modern processing, tap, bit breakage, screw sliding teeth rusting and other phenomena often occur.

  在很多的行业,但现代机械加工往往会出现丝锥,咬坏了,螺丝滑牙锈,等等,然而,出现这种情况有些老师会慢慢挑选,不仅浪费时间,延误工期,而且还会损害牙齿,导致工件报废。

  In many industries, but modern mechanical processing often appears taps, bites, screw slippery teeth rust, and so on. However, in this case, some teachers will slowly select, not only waste time, delay the time limit, but also damage the teeth, leading to the scrap of the workpiece.

  数控刀片回收厂家告诉你丝锥断了怎么办?

  CNC blade recycler tells you what to do if the tap is broken?

  首先,倒一些润滑油,用锋利的发夹慢慢敲打或在断口上反方向切割,不时用铁片切割,或将手柄或六角螺母焊接在丝锥断口处,然后轻轻倒出;最常用的工具是一种特殊的工具:断锥拔牙器。原则是工件和分别与正、负电极,和电解液是在中间,导致工件的放电腐蚀水龙头,然后协助尖嘴钳拆除、损坏内孔。

数控刀片回收

  First, pour some lubricating oil, tap slowly with a sharp hairpin or cut in the opposite direction on the fracture, cut with iron pieces from time to time, or weld the handle or hexagonal nut at the tap fracture, and then gently pour it out; the most commonly used tool is a special tool: the tap-breaker and tooth extractor. The principle is that the workpiece and the positive and negative electrodes, respectively, and the electrolyte are in the middle, causing the workpiece to corrode the tap by discharge, and then assisting the sharp nipper to remove and damage the inner hole.

  如果没有,取钢辊顶部在丝锥裂纹处用小锤慢慢敲打,丝锥越敲越脆,最后敲出渣渣,或更简单,直接将丝锥螺孔破开活镗孔,重新扩孔攻丝;否则,在螺纹孔处将断裂的丝锥焊接平整,然后再地面平整,重新钻孔,虽然难度大,但可以慢慢钻孔;在断了的丝锥上凿一个槽,用螺丝刀将螺丝拧开。

  If not, tap the top of the steel roll slowly with a hammer at the crack of the tap, the more brittle the tap is, the more brittle the tap is, and finally tap the slag, or simpler, directly break the tap screw hole into a live boring hole, reaming and tapping; otherwise, the broken tap will be welded flat at the thread hole, and then the ground will be flat and drilled again, although it is difficult. But drill slowly; dig a slot in the broken tap and unscrew the screw with a screwdriver.

  丝锥坏了以后,如果锥筒的一部分留在孔外,可以用钳子夹住锥筒,慢慢旋出。该方法适用于小直径丝锥。如果丝锥在孔内断裂,直径较大且芯片在孔内堆积量较小,可使用专用或自制的三爪、四爪丝锥插入芯片夹持槽内,慢慢旋出;或者在丝锥上焊接一段螺栓,用扳手把它拧出来。破碎的水龙头不能分离出来时,您可以使用一个穿孔或硬碟针能抵抗水龙头,用手锤慢慢敲打,使水龙头出口相反的方向,但坏的水龙头肯定不能用,扔掉的话但不幸的是,只能让天津自来水恢复,所以你可以收回点成本。

  When the tap is broken, if part of the cone is left outside the hole, the cone can be clamped with pliers and slowly rotated out. This method is suitable for small diameter taps. If the tap breaks in the hole, the diameter is large and the chip stacks in the hole is small, special or self-made three-claw or four-claw taps can be inserted into the chip clamping groove and slowly rotated out, or a bolt can be welded on the tap and screwed out with a wrench. When the broken faucet can't be separated, you can use a piercing or hard disk needle to resist the faucet. You can tap the faucet slowly with a hammer to make the outlet of the faucet in the opposite direction, but the bad faucet can't be used. If you throw it away, unfortunately, only the Tianjin tap water can be restored, so you can recover some cost.

  以上是数控刀片回收厂家为大家整理的相关内容,想要了解更多内容,欢迎访问网站:http://www.hxdphs.com

  The above is the relevant content of NC blade recycling manufacturers for you. For more information, please visit the website: http://www.hxdphs.com.