• 地址:山东省济南市高新区邢村立交桥路北
  • 联系人:张经理
  • 手机:18605312229
新闻中心当前位置:首页-新闻中心

数控刀柄有哪些特色,数控刀柄的规范
What are the characteristics of NC tool holder?
数控刀柄类型的特色
Characteristics of CNC tool holder type
1.加工曲面类零件时,为了确保刀具切削刃与加工概括在切削点相切,而防止刀刃与工件概括发作干与,一般选用球头刀,粗加工用两刃铣刀,半精加工和精加工用四刃铣刀
1. When machining curved surface parts, in order to ensure that the cutting edge and the machining generalization are tangent at the cutting point, and prevent the cutting edge and the workpiece generalization from drying out, the ball-nosed cutter is generally used, the two-edge milling cutter is used for rough machining, the four-edge milling cutter is used for semi-finishing and finishing.
2.铣较大平面时,为了进步出产功率和进步加工外表粗糙度,一般选用刀片镶嵌式盘形铣刀
2. In order to improve output power and surface roughness, insert disc milling cutter is usually used when milling large plane.
3.铣小平面或台阶面时一般选用通用铣刀
3. general milling cutter is usually adopted when milling small plane or step surface.
4.铣键槽时,为了确保槽的尺度精度、一般用两刃键槽铣刀
4. when milling key grooves, in order to ensure the accuracy of the groove size, a two edge keyway cutter is usually used.
5.孔加工时,可选用钻头号孔加工类刀具
5. hole machining, you can use drill bit hole machining tool.
数控刀柄规范
Specification for CNC tool shank

数控刀片回收
国内应用的数控机床东西柄部及配用拉钉规范
Domestic application of CNC machine tool handle and specification for pulls
1.国家规范GB10944-89《主动换刀机床用7:24圆锥东西柄部40、45和50号圆锥柄》
1. national standard GB10944-89 "active tool change machine tool with 7:24 cone, handle 40, 45 and 50 taper shank".
2.国家规范所规则的拉钉,《主动换刀机床用7:24圆锥东西柄部40、45和50号圆锥柄用拉钉》
2. Drawing nails as stipulated in the national code, "Drawing nails for tapered shanks 40, 45 and 50 with 7:24 tapered East and West shanks for active tool changers"
3.日本规范JIS B6339-1986《加工中心机床用东西柄部及拉钉》
3. Japanese standard JIS B6339-1986 "machine tool handle and pull pin for machining center".
4.国家规范GB3837-83《机床东西7:24圆锥联合》
4. national standard GB3837-83 "machine tool things 7:24 cones joint"
TSG东西体系中的刀柄,其代号(按1990年国家规范报批稿)由四部分组成,各部分的意义如下:
The code name of the knife handle in the East-West system of TSG (submitted for approval according to the 1990 National Standards) consists of four parts. The meaning of each part is as follows:
JT-表明东西柄型代码。
JT- indicates the handle code.
45-对圆锥柄表明锥度标准。
45- shows taper standard for conical shank.
Q32-表明东西的标准。
Q32- shows the standard of things.
120-表明刀柄的作业长度。
120- indicates the length of the handle.
它所表明的东西为:主动换刀机床用7:24圆锥东西柄(GB10944),锥柄为45号,前部为弹簧夹,最大夹持直径32mm,刀柄作业长度(锥柄大端直径φ57.15mm处到弹簧夹头前端面的间隔)为120mm。
What it shows is: 7:24 tapered East-West handle (GB10944), 45 tapered shank, spring clamp at the front, maximum clamping diameter 32 mm, tool shank length (the gap between the tapered shank big end diameter of 57.15 mm and the front face of spring clamp) 120 mm.
济南恒鑫刀具有限公司,对数控刀片回收感兴趣的朋友可以关注我们http://www.hxdphs.com,更多精彩内容知识敬请期待。
Jinan Hengxin Tool Co., Ltd., the CNC blade recycling interested friends can pay attention to our http://www.hxdphs.com, more wonderful content knowledge please look forward to.