你好,欢迎浏览济南恒鑫刀具回收有限公司网站!
数控刀片回收

专心 专注 专营

服务好 效率高 诚信好 价格高

数控刀片回收

联系电话:

18605312229

当前位置:首页>新闻中心>行业新闻>数控开料机刀具夹装应注意哪些

数控开料机刀具夹装应注意哪些

来源:http://www.hxdphs.com/ 日期:2020-05-12 发布人:admin

  数控开料机开料槽铣料孔,木工铣刀是常用的消耗品;刀具装夹过程中注意事项

  The CNC cutting machine is used to cut the slot and mill the hole, and the woodworking milling cutter is a common consumable; precautions in the process of tool clamping
  刀具装夹的基本过程
  Basic process of tool clamping
  数控机床主轴电机采用弹簧卡盘(又称机筒)夹紧刀具,刀具的夹紧精度直接影响雕刻的质量。因此,刀具的加载必须按照以下步骤进行
  The spindle motor of CNC machine tool uses spring chuck (also known as barrel) to clamp the cutter. The clamping accuracy of cutter directly affects the quality of carving. Therefore, the loading of the tool must be carried out according to the following steps
数控刀片回收
  卡盘头有较多裂纹,要求每次装夹前,卡盘头必须用汽油或WD40清洗剂清洗,并检查清除卡盘头间隙残留。
  There are many cracks in the chuck head. It is required that the chuck head must be cleaned with gasoline or WD40 detergent before clamping each time, and the clearance of the chuck head shall be checked and removed.
  卡盘通过轴端锥孔的接触与轴配合。如果接触不好,刀具不能正确安装,锥面应处于良好的接触状态。在使用刀具之前,用汽油或WD40清洁剂清洗夹头和轴锥。
  The chuck fits with the shaft through the contact of the taper hole at the shaft end. If the contact is not good and the cutter cannot be installed correctly, the cone should be in good contact condition. Before using the tool, clean the collet and shaft cone with gasoline or WD40 cleaner.
  把查克放进压缩帽,轻轻地把查克压缩弹簧,压到古怪的一部分帽凹夹头槽,宜兴帽子状态沿着箭头方向查克均匀,可以加载到压缩帽。查克的状态压缩帽。
  Put chuck into the compression cap, gently press chuck compression spring into the odd part of the cap concave collet groove, Yixing hat state is evenly chuck along the arrow direction, and can be loaded into the compression cap. Chuck's state compression cap.
  夹头和压帽安装在机床主轴上,将机床的圆柱形手柄擦拭干净,放入夹紧孔内。确认夹头和工具放置正确位置后,用手将压盖拧到位,然后用扳手均匀拧紧压盖,直至工具牢固夹紧
  The collet and the pressing cap are installed on the spindle of the machine tool, the cylindrical handle of the machine tool is wiped clean and put into the clamping hole. After confirming that the collet and tool are in the correct position, screw the gland in place by hand, and then tighten the gland evenly with a wrench until the tool is firmly clamped
  松开刀具时,用扳手反方向拧紧夹帽。如需更换卡盘时,松开夹紧帽,取出卡盘和刀具,取出刀具,沿箭头方向用力推动卡盘,将其推出,然后根据需要更换其他口径的卡盘。
  When loosening the tool, tighten the clamping cap with the wrench in the opposite direction. If the chuck needs to be replaced, loosen the clamping cap, take out the chuck and the tool, take out the tool, push the chuck in the direction of the arrow, push it out, and then replace the chuck with other caliber as required.
  以上是数控刀片回收公司小编为大家介绍的想要了解更多内容,欢迎访问网站:http://www.hxdphs.com
  The above is the introduction of CNC blade recycling company, welcome to visit the website: